Hale HPX75-B23 Firefighting Pump

Hale HPX75-B23 Firefighting Pump
545-00132-000

The Hale HPX75-B23 Firefighting Pump shall be capable of meeting the NFPA 1906 performance rating 50 GPM @ 250 PSI.

The Hale HPX75-B23 has flows ranging from 15 GPM @ 380 PSI to 135 GPM @ 80 PSI. The Hale high pressure pump range are designed to be tough and dependable performers. The HPX (Max Stream) is conveniently designed for easy installation by truck builders.

Performance
The pump/engine shall be capable of meeting the NFPA 1906 performance rating 50 GPM @ 250 PSI. Typical pump performance from 5 foot draft at sea level shall be:
15 GPM @ 380 PSI
70 GPM @ 220 PSI
135 GPM @ 80 PSI

Pump
The pump body shall be made of anodized alloy aluminum castings coupled together with a stainless steel band clamp with an O-ring seal which allows quick pump volute removal for servicing. The pump end shall be factory hydrostatically tested to 500 PSI. The impeller shall be bronze and 4.88 inches (123.8 mm) in diameter. The renewable clearance ring shall be made of bronze to inhibit galvanic corrosion. To obtain the required pressures, a built-in oil bath lubricated gearbox shall be provided between the pump end and engine. The gearbox shall be coupled together with a stainless steel band clamp. The pump shaft seal shall be an automatically adjusting, maintenance free, mechanical type. The pump body shall be equipped with a petcock drain valve.

Control Panel:
Discharge gauge
Priming lever
Start button
ON/OFF switch
Oil warning light
Choke
Throttle control

Priming
The pump shall be equipped with an exhaust venturi primer of brass and stainless steel construction. The primer shall be capable of priming at 13 feet lift. The primer shall be actuated with a spring return, single control lever located at the operator’s panel. The primer to pump line shall be equipped with an automatic check valve for priming from an open body of water and a manual shut-off for pumping from a pressurized water source.

Suction/Discharge
The suction and discharge ports shall be female pipe thread, designed and located to accept applicable hose thread adapters (2.0” NPT Suction, 1.5” NPT Discharge).

Engine
The engine shall be a 4 cycle gasoline Briggs and Stratton Vanguard 386447 series V-Twin, overhead valve, air cooled design. Engine rating shall be 23 BHP at 3600 RPM. Engine displacement shall be 627cc and shall be designed to meet current CARB (California Air Resources Board) and EPA (Environmental Protection Agency) standards. A 12-volt electric system shall be provided with electric starter and a 16 amp alternator. Engine shall be equipped with a residential muffler with USDA approved spark arrestor.

Mounting Platform
The pump/engine shall be isolation mounted onto a steel base plate.

Instrumentation
The pump shall be available with a remote mounted control panel. This panel shall include a throttle lever, primer lever, master switch, starter button, choke control, a 2.5 inch liquid filled discharge gauge and an oil pressure warning light.

Features
Flows ranging from 15 GPM @ 380 PSI to 135 GPM @ 80 PSI
Ultra-reliable Briggs & Stratton 23-HP 4-cycle V-Twin gasoline engine
Electric start with recoil backup
Anodized aluminum alloy pump head and body
Pump head and body coupled together with stainless steel band clamp for easy serviceability
Bronze impeller and renewable wear ring
Self-adjusting mechanical seal
Exhaust gas venturi priming
2.0” NPT suction connection; 1.5” NPT discharge
Applications/Solutions
Fire OEMs
Firefighting - Wildland Forestry

Warranty 3 Year Warranty
Weight 157 lbs (71 kg)
Brand Powerflow
Length 21 inches (533 mm)
Width 18 inches (457 mm)
Height 20 inches (508 mm)

Specifications: